Apollo Solar T80HV TurboCharger Charge Controller MPPT Battery Charge Controller, 80 amp, 200 Voc

 The T80HV is the only MPPT charge controller that works with the newer higher voltage PV modules. Specifically, the Sanyo HIT 200 modules have Vmp of 51.75v at 50°C which will not charge a 48 volt battery, but they generate up to 79.88 volts open circuit at -40°C. Two of these modules in a series string will generate 103 volts at Vmp, but the Voc is almost 160 volts which will destroy all the 140/150 volt charge controllers. The T80HV is designed to operate up to 200 Voc and 160 Vmp and works with the Sanyo HITs.

Apollo T80 Charge Controller, 80 amp MPPT Battery Chnarge Management System

Power and Control in a Single Device
The T80 TurboCharger^TM integrates Maximum Power Point Tracking, battery charge management, state of charge information and communications into a single device. With 80 Amps continuous output, the T80 has the largest capacity in the industry by over 30%.

Continuous Power Rating Up to 113°F (45°C) Ambient
The T80 TurboCharger^TM produces full-rated power without de-rating up to 45°C ambient temperature. Above that, the output current is reduced gradually to protect the life of the T80 and then automatically ramped up as the temperature decreases. high efficiency power circuits and robust thermal design minimize heat generation. The internal temperature-controlled variable speed fan runs just fast enough to maintain optimum reliability.

Energy Monitor Built In
The T80 includes a built-in Energy Monitor using TriMetric^TM Technology from Bogart Engineering. The monitor tracks power production and consumption to calculate the energy remaining in the batteries. State of Charge (SOC) is displayed in Percent Full, Amp-hours, Watt-Hours, and Bar-Graph format. In addition, 90 days of energy-harvest history is stored in the T80.

Enhanced Battery Performance and Life
The T80 supports Flooded Lead Acid (FLA), GEL and Absorbed Glass Mat (AGM) batteries. Four-stage charging with adjustable set points for all parameters.

Optimum MPPT/Charging Efficiency Cuts Costs
The T80 captures up to 35% more power from the photovoltaic (PV) array with patent-pending MPPT technology. The Apollo MPPT algorithm starts early and locks onto the peak power during rapidly changing insolatrion and temperature. The T80 dramatically cuts the cost of a PV system by reducing the number of PV panels required, eliminating the need for heavy gauge wiring, and increasing the life of the storage batteries.

Integral Performance-and-Updated Communications
The slot for optional add-in cards provides data communication to Remote Displays, PCs and the Internet. System performance can be monitored remotely and the T80 accepts software upgrades using a PC and the Remote Display's SD Memory Card.

Features

• 80 Amps continuous output at up to 113°F (45°C) ambient temperature.
• Built-in Battery Energy Monitor
• Patent Pending MPPT Provides Best Energy Harvest Available
• Wire the PV modules in series up to 72 VDC nominal (140 Voc max)
• Parallel T80's for higher currents: Stack Up to 16 units
• Precision charging of 12/24/36/48 volt batteries with one-minute set-up and Fail-safe calculated defaults
• Wired/Wireless Remote Displays

Apollo Solar T80 MPPT Charge Controller Turbo Charger^TM Specifications

• Maximum output current: 80 amps continuous at up to 113°F (45°C) ambient temperature
• Battery voltages: 12, 24, 36, or 48 VDC nominal
• Max PV input current: 70 amps
• Input voltage range: 16 to 112 VDC operating, 140 VDC Maximum Open Circuit Voltage
• Max PV array power: 5200 Watts (maximum when equalizing a 48v battery to 64v at 80 amps)
• Charge regulation modes: Bulk, Absorption, Float, Standby, Auto Equalization, and Manual Equalization
• MPPT Features: Apollo Solar patent-pending MPPT algorithm harvests the optimum power under all conditions of clouds or temperature
• Battery temperature compensation: 6.0 mV per °C per 2 volt cell
  
• Display: Built-in 4-line 20-character LCD with back light
• Status Reporting: LCD status screen displays input voltage and current, Output voltage and current, Charge-mode, and Battery State-Of-Charge (SOC)
• Data Logging: Logs energy harvested for 90 days. LCD displays Watt-hours, kW-hours, Amp hours, and hours each day that Float mode is active.
• Energy Monitor: LCD shows SOC (state-of-charge) in a fuel gauge style bar graph as well as % Full, Amp-hours, Watt-hrs and present charge or discharge current. A 50 mV / 500 amp shunt is required to use the Energy Monitor features.
• Auxiliary relays: Two independent relays with form A (SPST) contacts for control of external devices. Configurable as NO or NC. Contact rating 1/2 amp, 50 VDC.
• Operating Temperature and de-rating: Full power output at 45°C ambient output current automatically ramped down above 45°C and softly restored as temperature decreases.
• Standby Power: Less then 2 watts
• Data Communication Options: Card slot for optional Apollo Network and Wireless link to Remote Display
• Connectors: Power lugs accept 14 to 10. No. 2 wire recommended
• Conduit knockouts: One 1" or 1.25" and one 0.5" or 0.75" on left side. Two 0.5" or 0.75" on back. Two 1" or 1.25" on bottom. Bottom holes line up with power connectors.
• Certifications: UL1741, CSA C22.2 No. 107.1
• Environmental Rating: Indoor Type 1 (Not intended for use in extremely damp locations.)
• Included Accessory Kit: Apollo Shunt Board and cable, battery monitor cable, and Battery Temperature Sensor.

Shipping Weight: 22 lbs. (10 kg)
Shipping Dimensions (HWD): 21”x 12.5 x 8.5” (530 x 318 x 216 mm)

Weight: 16 lbs (7.3 kg)
Unit Dimensions (HWD): 15.2 “x 8.5” x 4.4” (387 x 216 x 111 mm)